September 8, 2008
PM Service – Preventative maintenance programs.

Quality Service
Performance PM SM ensures that your vehicle will get the best parts, premium oil and filters, and that it will be serviced exclusively by factory- trained and certified technicians.  That means knowing the job is done right the first time, every time.

Consistency & Value
With Performance PM you can count on outstanding service wherever you need it. .

Convenience
International dealerships feature extended service hours, and International's vast parts inventory network, the most hard to find parts are readily available. .

Four Program Inspection Levels
  • Quick Lube (30 point inspection)
  • “A” Dry  (71 point inspection)
  • “A” Wet (71 point inspection)
  • “B” Wet (83 point inspection)

Dry does not include engine oil and filters.

Versatility
Performance PM can be purchased the way that’s best for you: you can participate on a job-by-job basis, or you can pre-purchase and ensure low prices for an extended period of time. You don’t have to make any unwanted commitments to take advantage of Performance PM. Nor do you have to drive an International truck; all makes are eligible for the program.

Additionally, Performance PM services can be paid for by credit card, Fleet Charge® or Diamond AdvantageSM , and are also available through service contracts on new and used vehicles.

Items Included Depending on Inspection Level Chosen
  1. Turn key on – check fault codes
  2. Start engine – observe instrument operation
  3. Apply and release brakes 10 times
  4. low air buzzer & light
  5. that dash parking brake value pops out at 35psi
  6. clutch peal free travel
  7. clutch brake operation
  8. transmission hi-low splitter or two-speed axle control
  9. clutch and/or neutral safety switch
  10. HVAC duct defrosters, air vents, fan speed and controls
  11. HVAC duct temperature, record
  12. windshield wipers & washers
  13. horns, electric, & air
  14. interior lights, turn indicators & dash lights
  15. door glass and mirror controls
  16. seats, seat belts, & floor mats
  17. tractor hand value
  18. power divider shift operation
  19. 5th wheel slider air lock operation
  20. air suspension dump value
  21. ABS antilock monitor light, if equipped
  22. parking brake
  23. hydraulic brake booster, back-up motor, warning light & buzzer
  24. for 3 DOT approved warning triangles
  25. for fire extinguisher
  26. seals (boots) – shifter, clutch, & steering shaft
  27. DOT sticker validation
  28. Take oil sample
  29. Drain engine oil
  30. cab & body appearance – condition & damage
  31. air fairings, extenders & brackets
  32. license plate holder & light
  33. Check lighting – headlights, tail/stop, turn signal, marker, backup, reflectors & work lights
  34. doors – access & latches
  35. hood latches
  36. steps & grab handles
  37. fuel tank straps & fuel fill cap
  38. batteries – visual inspection of cables, clamping, corrosion, & fluid levels, fill if necessary
  39. vertical exhaust, muffler, clamps, brackets
  40. mirrors – condition & mounts
  41. mud flaps / splash guards
  42. trailer electric / air hoses, glad hands
  43. cab air ride system
  44. 5th wheel – mounting & jaws
  45. frame & crossmembers
  46. pintle hook & safety chain loops
  47. body – inspect doors, cargo latches, & lift gates
  48. tires & wheels
  49. radiator & shroud
  50. Pressure test cooling system
  51. Test DCA, extended life & freeze protection
  52. belts – visual inspection for wear & tension
  53. hoses – condition and/or leaks
  54. hose & wire routing, securing
  55. exhaust – mounting, clamping & evidence of leaks
  56. air cleaner housing, air-to-air piping & clamping
  57. air cleaner restriction gauge
  58. alternator – visual inspection
  59. wiper blade condition
  60. starting system – visual inspection
  61. steering shaft, shaft U-joints, box mounting, pitman arm & drag link
  62. power steering fluid level
  63. master cylinder fluid level
  64. Top off washer fluid
  65. Drain water from fuel water separator
  66. Change fuel filter
  67. Change fuel water separator element
  68. Change water filter
  69. APAD’S controller for fault codes
  70. for oil leaks – engine, steering, axle, transmission & differential
  71. engine & transmission mounts
  72. transmission oil level
  73. drivelines & U-joints
  74. transmission & differential yoke for play
  75. differential oil level
  76. springs, hangers, & shocks
  77. tie rod ends
  78. air tanks, air dryer – drain & observe for oil & water
  79. horizontal exhaust, muffler, clamps, & brackets
  80. brake rod travel
  81. brake lining and/or pad wear
  82. ABS wiring & routing
  83. PTO, wetline pump & hose routing
  84. air ride height
  85. Install oil plug & torque
  86. Raise front axle – inspect king pins & wheel bearings
  87. Grease king pins following the “turn & load” procedure
  88. Grease & complete chassis
  89. Change oil filter
  90. Fill engine with oil & run, recheck level
  91. automatic transmission fluid level
  92. Install PM sticker in window
  93. Reset oil change light
  94. Review PM sheet with Service Writer




Toll Free: Tampa - 800.741.7566 | Sarasota - 800.226.9200 | Central Florida - 800.624.2411
e-contact@sunstateintl.com | © 2007 Sun State International Trucks | Terms of Use | Privacy Policy